Multi-Light Bar Pairing Guide: Control Multiple Quntis Light Bars with one Remote

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the “+” and “–” buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the “+” and “–” buttons on the wireless controller at the same time.
3. 3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Within 5 seconds after turning on the light bar, press and hold the top cover with one hand and rotate the outer ring with the other hand.
2. When the light flashes, the light bar and wireless controller are paired.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the “+” and “–” buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the【Color Temperature】and【Brightness】buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the wireless controller included in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the【Color Temperature】and【Brightness】buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 7 seconds. The front light will flash to indicate successful unpairing.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 7 seconds. The front light will flash to indicate successful unpairing.

This light bar also supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 7 seconds. The front light will flash to indicate successful unpairing.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 7 seconds. The front light will flash to indicate successful unpairing.

This light bar also supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 7 seconds. The front light will flash to indicate successful unpairing.

This light bar also supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the【Color Temperature】and 【Brightness】buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. 2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking. When the blinking stops, the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 5 seconds. The front light will flash to indicate successful unpairing.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 5 seconds. The front light will flash to indicate successful unpairing.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】 button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 5 seconds. The front light will flash to indicate successful unpairing..

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 12 seconds after turning on the light bar, tap and hold the【On/Off】button for about 4 seconds to start pairing.
3. Wait for the front light to start blinking, which indicates that the pairing is successful.
4. After the blinking stops, test the pairing by adjusting the brightness or color temperature with the wireless controller.
5. To unpair, turn on the light, then tap and hold the【Brightness】button for about 5 seconds. The front light will flash to indicate successful unpairing..

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.

Each light bar is pre-paired with the remote in the package. If the controller fails to control the light bar, or if you replace the controller, please re-pair them as follows:

1. Unplug the light bar, then plug it back in to restart it.
2. Within 5 seconds after it powers on, tap and hold the【Color Temperature】and【Brightness】buttons on the wireless controller at the same time.
3. Wait for the light bar to start blinking. When it stops blinking, the pairing is successful. Test the pairing by adjusting the brightness or color temperature with the wireless controller.

This light bar supports multi-light control, allowing one wireless controller to control two or more light bars at the same time.

You can use the same pairing procedure to connect the same wireless controller to multiple light bars.